Počet záznamov: 1
Vplyv konštrukcie pílového kotúča na kvalitu vytvoreného povrchu pri priečnom pílení smrekového reziva na kapovacej pokosovej píle
SYS 0075465 LBL 00000naa^^22^^^^^^^^450 005 20190402085759.4 100 $a 20141028d m y0sloc0103 ba 101 0-
$a slo $d eng 102 $a SK 200 1-
$a Vplyv konštrukcie pílového kotúča na kvalitu vytvoreného povrchu pri priečnom pílení smrekového reziva na kapovacej pokosovej píle $d Effect of the saw blade construction on the surface quality when transverse sawing spruce lumber on crosscut miter saw $f Richard Kminiak 215 $c Obr., tab. 320 $a Lit. 330 $a The article deals with problematic of spruce wood cross-cutting. It focuses on the impact of the saw blades teeth number and use of chip limiting device saw blade on the surface quality during cross-cutting. Article is based on an experiment in which was used four saw blades with SK plates with uniform diameter (D = 250 mm) and uniform angular geometry (α = 15°, β = 60°, γ = 15°). Three saw blades were characterized by different numbers of teeth (z = 24, 40 a 60) and one saw blade was chip limiting device saw blade. For the experiment were used tangentially sawn spruce samples with absolute humidity wa = 12 ± 1%, and 50 mm of thickness. Cutting the spruce test samples was conducted to crosscut miter saw BOSCH GCM 10 S PROFESIONAL with the movement of the saw blade on a circular arc at a constant cutting speed (vc= 62 m×s−1) and at a sliding force (Fp = 15 N). The experiment showed that the surface quality - the arithmetic mean deviation of the roughness profile depending on the used saw blade varies from 4 to 18 μm. The experiment demonstrated that the increase in the number of teeth of the saw blade increases the surface quality and that the use of chip limiting device greatly improves the quality of the surface. 330 $a Cieľom tohto článku je sledovanie zmeny drsnosti povrchu v procese priečneho pílenia smrekových vzoriek v závislosti od vybraných premenných, počtu zubov pílových kotúčov a modelu delenia. 463 -1
$1 001 sldk_un_cat*0075362 $1 011 $a 1336-3824 $1 200 1 $a Acta Facultatis Xylologiae Zvolen $e vedecký časopis Drevárskej fakulty $v Roč. 56, č. 2 (2014), s. 87-96 $1 210 $a Zvolen $c Technická univerzita vo Zvolene $d 2014 610 1-
$9 sldk_un_auth*h012599 $a kapovacie píly $X cross-cut sawing machines 610 1-
$9 sldk_un_auth*h042015 $a pílové zuby $X saw teeth 610 1-
$9 sldk_un_auth*h002903 $a pílové kotúče $X circular saw blades 610 1-
$9 sldk_un_auth*h011050 $a triesky $X chips 610 1-
$9 sldk_un_auth*h013345 $a kvalita povrchu $X quality of surface 675 $a 621.934.42 $v 1. stred. $z slo 675 $a 630*822.8 $v 1. stred. $z slo 700 -1
$3 sldk_un_auth*0010060 $a Kminiak $b Richard $f 1984- $p TUZDFOD $4 070 $T Katedra obrábania dreva 801 -0
$a SK $b ZV001 $c 20141028 $g AACR2 856 4-
$u https://df.tuzvo.sk/sites/default/files/10-2-14-kminiak_1.pdf
Počet záznamov: 1